Differences

This shows you the differences between two versions of the page.

--- en:ost:ccds:setup [2014/11/15 23:35] – created msteinke
+++ en:ost:ccds:setup [2021/03/31 07:53] (current) – [STF-8300M] rhainich
@@ Line 1: / Line 1: @@
 ====== CCDs Setup ======
+===== QHY600M =====
+   * will follow soon ...
 ===== STF-8300M =====
-First light
-[{{:ost:ccds:windradani_small.gif?nocache|First light, Wind wheels in Golm}}] [{{:ost:ccds:wissenschaft.jpg?350|One of the buildings in the Wissenschaftspark Golm}}]
+==== First light ====
+<WRAP group 70%>
+<WRAP half column>
+[{{ :ost:ccds:windradani_small.gif?nocache |Wind turbines near Golm}}]
+</WRAP>
+<WRAP half column>
+[{{ :ost:ccds:wissenschaft.jpg?335 |One of the buildings in the Wissenschaftspark Golm}}]
+</WRAP>
+</WRAP>
+==== Assembling the filter wheel and the OAG ====
-===== ST-8/7 =====
+The goal of this task is to mount or dismount the filter wheel and the off-axis guider (OAG) to the CCD. The procedure in short:
-==== Assembling the filter wheel ====
-The goal of this task is to mount or dismount the filter wheel to the CCD. The operation is demonstrated by the following pictures of the ST-8. The procedure in short:
+  - to open the camera, loose the screws from the cover, see Figure 1.
+  - open the case of the filter wheel and mount the backplate of the filter wheel (along with the mechanics and the electronics) to the CCD, see Figure 2.
+  - insert the individual filters and the spacer rings in the filter holder and mount the cover panel on top, see Figure 3. and 4.
+  - attach the filter holder to the backplate of the filter wheel (be careful with the sensor for the filter position), see Figure 2. and 4.
+  - screw the cover of the filter wheel to the backplate of the filter wheel, see Figure 5.
+  - attach the OAG to the filter wheel, see Figure 6.
+  - adjust the mirror of the OAG (the mirror is kept in place by means of a small lateral screw), see Figure 6.
+  - attach the top cover and the T2 adapter to the OAG, see Figure 7.
+  - connect the cable of the filter wheel to the STF-8300, see Figure 8.
+  - fit the ST-i in the OAG, see Figure 9.
+  - READY :-)
-  - Open the camera. Loose the screws from the cover, see Figure 1.
+<WRAP group>
-  - Open the case of the filter wheel and mount the empty cover of the filter wheel to the CCD, see Figure 2.
+<WRAP third column>
-  - Now attach the filter wheel and the case of the adaptive optics module (AO), see Figure 3.
+[{{ :ost:ccds:stf8300_cover.jpg?265 | 1. Cover of the STF-8300 }}]
-  - Attach the deflecting mirror and AO case, see Figure 4. /* ist Umlenkspiegel "deflecting mirror"? */
+</WRAP>
-  - Connect the cables for:
+<WRAP third column>
-    * The AO control (flat ribbon cable)
+[{{ :ost:ccds:stf8300_filter_wheel.jpg?265 | 2. Backplate of the filter wheel mounted to the SFT-8300 (the red circles mark the corresponding screws, the blue circle marks the sensor for the filter wheel position)}}]
-    * The power supply
+</WRAP>
-  - Ready :-)
+<WRAP third column>
+[{{ :ost:ccds:stf8300_filter_wheel_2.jpg?265 | 3. Filter holder with filters and spacer rings}}]
+</WRAP>
+</WRAP>
-<columns 100% 33% 33% 33%>
-[{{ :ost:ccds:st8_open_lid.jpg?300 |1: ST8 and cover}}]
-<newcolumn>
+<WRAP group>
-[{{ :ost:ccds:fw_screws_2.jpg?300 |3: Mount the filter wheel}}]
+<WRAP third column>
+[{{ :ost:ccds:stf8300_filter_wheel_3.jpg?265 | 4. Filter wheel with inserted filter holder (the red circles mark the screws that attach the cover to the filter holder, the blue circles mark the screws that attach the filter holder to the backplate of the filter wheel)}}]
+</WRAP>
+<WRAP third column>
+[{{ :ost:ccds:stf8300_filter_wheel_4.jpg?265 | 5. Filter wheel with the cover}}]
+</WRAP>
+<WRAP third column>
+[{{ :ost:ccds:stf8300_oag_1.jpg?265 | 6. Filter wheel with the OAG}}]
+</WRAP>
+</WRAP>
-<newcolumn>
-[{{ :ost:ccds:fw_st8_ports.jpg?300 |5: Connect the cables}}]
-</columns>
+<WRAP group>
+<WRAP third column>
+[{{ :ost:ccds:stf8300_oag_2.jpg?265 | 7. Filter wheel with the OAG and T2 adapter}}]
+</WRAP>
+<WRAP third column>
+[{{ :ost:ccds:stf8300_side.jpg?265 | 8. Side view of the STF-8300}}]
+</WRAP>
+<WRAP third column>
+[{{ :ost:ccds:stf8300_complete.jpg?265 | 9. STF-8300 with filter wheel, OAG, and ST-i}}]
+</WRAP>
+</WRAP>
+===== ST-8/7 =====
+==== Assembling the filter wheel ====
+The goal of this task is to mount or dismount the filter wheel to the ST-7 of ST-8. The operation is demonstrated by the following pictures of the ST-8. The procedure in short:
-<columns 100% 33% 33% 33%>
+  - open the camera by loosing the screws from the cover, see Figure 1.
-[{{ :ost:ccds:fw_case.jpg?300 |2: Case and filter wheel}}]
+  - open the case of the filter wheel and mount the empty cover of the filter wheel to the CCD, see Figure 2.
+  - now attach the filter wheel and the case of the adaptive optics module (AO), see Figure 3.
+  - attach the deflecting mirror and AO, see Figure 4.
+  - connect the cables for:
+    * the AO control (flat ribbon cable)
+    * the power supply
+  - READY :-)
-<newcolumn>
+<WRAP group>
-[{{ :ost:ccds:fw_screws_1.jpg?300 |4: Adaptive Optics}}]
+<WRAP third column>
+[{{ :ost:ccds:st8_open_lid.jpg?265 |1: ST8 and cover}}]
+</WRAP>
+<WRAP third column>
+[{{ :ost:ccds:fw_screws_2.jpg?265 |3: Screw positions on the filter-wheel backplate (green circles) and the AO case (red circles)}}]
+</WRAP>
+<WRAP third column>
+[{{ :ost:ccds:fw_st8_ports.jpg?265 |5: ST-8 with the cable connections}}]
+</WRAP>
+</WRAP>
-<newcolumn>
-[{{ :ost:ccds:fw_and_st8.jpg?300 |6: Complete}}]
-</columns>
+<WRAP group>
+<WRAP third column>
+[{{ :ost:ccds:fw_case.jpg?265 |2: ST-8 with the attached filter-wheel case}}]
+</WRAP>
+<WRAP third column>
+[{{ :ost:ccds:fw_screws_1.jpg?265 |4: Adaptive optics module}}]
+</WRAP>
+<WRAP third column>
+[{{ :ost:ccds:fw_and_st8.jpg?265 |6: Assembled camera}}]
+</WRAP>
+</WRAP>