Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
en:ost:telescope:probleme [2021/12/07 16:39] – [ST-8: shutter error] rhainich | en:ost:telescope:probleme [2022/07/25 10:57] (current) – [Telescope:] rhainich | ||
---|---|---|---|
Line 170: | Line 170: | ||
===== Telescope: ===== | ===== Telescope: ===== | ||
+ | ==== Focuser of the CDK20 does not run the complete range of ~35000μ ==== | ||
+ | |||
+ | <WRAP group> | ||
+ | <WRAP twothirds column> | ||
+ | **Problem description: | ||
+ | PWI3 shows clearly negative position values when driving in or the focuser does not run in the positive range (when driving out) up to the maximum ~35000μ. | ||
+ | |||
+ | **Solution: | ||
+ | The focuser has " | ||
+ | </ | ||
+ | <WRAP third column> | ||
+ | {{ ost: | ||
+ | </ | ||
+ | </ | ||
==== Wobbling Camera/ | ==== Wobbling Camera/ | ||
Line 210: | Line 224: | ||
===== Cameras: ===== | ===== Cameras: ===== | ||
+ | <WRAP group> | ||
+ | <WRAP twothirds column> | ||
==== Ice on the camera ==== | ==== Ice on the camera ==== | ||
- | |||
- | [{{ ost: | ||
**Description of the problem:** | **Description of the problem:** | ||
Line 218: | Line 232: | ||
**Solution: | **Solution: | ||
- | The cameras' | + | The cameras' |
==== ST-8: shutter error ==== | ==== ST-8: shutter error ==== | ||
Line 228: | Line 242: | ||
In this case the communication between the camera and //CCDops// is disturbed or the sensors for the shutter position do not work properly. Therefore, the software does not know whether the shutter is closed or not. It also could be that the shutter is indeed not moving as expected. In each case, it is often sufficient to switch off the camera and to disconnect it from the power supply. However, sometimes it is necessary to detach the camera from the telescope and to very carefully shake the camera a bit. Afterwards, the sensors of the shutter usually deliver proper data again. | In this case the communication between the camera and //CCDops// is disturbed or the sensors for the shutter position do not work properly. Therefore, the software does not know whether the shutter is closed or not. It also could be that the shutter is indeed not moving as expected. In each case, it is often sufficient to switch off the camera and to disconnect it from the power supply. However, sometimes it is necessary to detach the camera from the telescope and to very carefully shake the camera a bit. Afterwards, the sensors of the shutter usually deliver proper data again. | ||
- | <WRAP group> | ||
- | <WRAP twothirds column> | ||
==== Maxim DL: Two SBIG cameras cannot be simultaneously connected ==== | ==== Maxim DL: Two SBIG cameras cannot be simultaneously connected ==== | ||
Line 240: | Line 252: | ||
</ | </ | ||
<WRAP third column> | <WRAP third column> | ||
+ | [{{ ost: | ||
+ | \\ | ||
+ | \\ | ||
+ | \\ | ||
[{{ ost: | [{{ ost: | ||
</ | </ | ||
</ | </ | ||
+ | |||
==== CCDops does not find the filter wheel ==== | ==== CCDops does not find the filter wheel ==== | ||
**Description of the problem:** | **Description of the problem:** | ||
- | '' | + | //CCDops// does not find the filter wheel of the STF8300 camera although the filter wheel is rotating when the power is switched on. |
**Solution: | **Solution: | ||
- | The filter wheel needs to be reinitialized. The corresponding menu can be found via //Filter// and //Filter Setup//. Select the " | + | The filter wheel needs to be reinitialized. The corresponding menu can be found via '' |
Line 259: | Line 276: | ||
- | ====== | + | ====== |
++++ GM 4000 Mount: Tracking error | | ++++ GM 4000 Mount: Tracking error | |