Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
en:ost:ccds:setup [2016/10/24 00:10] – [Assembling the filter wheel and the OAG] rhainich | en:ost:ccds:setup [2021/03/31 07:53] (current) – [STF-8300M] rhainich | ||
---|---|---|---|
Line 1: | Line 1: | ||
====== CCDs Setup ====== | ====== CCDs Setup ====== | ||
+ | |||
+ | ===== QHY600M ===== | ||
+ | * will follow soon ... | ||
===== STF-8300M ===== | ===== STF-8300M ===== | ||
Line 6: | Line 9: | ||
==== First light ==== | ==== First light ==== | ||
- | <WRAP group> | + | <WRAP group 70%> |
<WRAP half column> | <WRAP half column> | ||
[{{ : | [{{ : | ||
Line 32: | Line 35: | ||
<WRAP group> | <WRAP group> | ||
<WRAP third column> | <WRAP third column> | ||
- | [{{ : | + | [{{ : |
</ | </ | ||
<WRAP third column> | <WRAP third column> | ||
- | [{{ : | + | [{{ : |
</ | </ | ||
<WRAP third column> | <WRAP third column> | ||
- | [{{ : | + | [{{ : |
</ | </ | ||
</ | </ | ||
Line 45: | Line 48: | ||
<WRAP group> | <WRAP group> | ||
<WRAP third column> | <WRAP third column> | ||
- | [{{ : | + | [{{ : |
</ | </ | ||
<WRAP third column> | <WRAP third column> | ||
- | [{{ : | + | [{{ : |
</ | </ | ||
<WRAP third column> | <WRAP third column> | ||
- | [{{ : | + | [{{ : |
</ | </ | ||
</ | </ | ||
Line 58: | Line 61: | ||
<WRAP group> | <WRAP group> | ||
<WRAP third column> | <WRAP third column> | ||
- | [{{ : | + | [{{ : |
</ | </ | ||
<WRAP third column> | <WRAP third column> | ||
- | [{{ : | + | [{{ : |
</ | </ | ||
<WRAP third column> | <WRAP third column> | ||
- | [{{ : | + | [{{ : |
</ | </ | ||
</ | </ | ||
Line 73: | Line 76: | ||
==== Assembling the filter wheel ==== | ==== Assembling the filter wheel ==== | ||
- | The goal of this task is to mount or dismount the filter wheel to the CCD. The operation is demonstrated by the following pictures of the ST-8. The procedure in short: | + | The goal of this task is to mount or dismount the filter wheel to the ST-7 of ST-8. The operation is demonstrated by the following pictures of the ST-8. The procedure in short: |
- | - Open the camera. Loose the screws from the cover, see Figure 1. | + | - open the camera |
- | - Open the case of the filter wheel and mount the empty cover of the filter wheel to the CCD, see Figure 2. | + | - open the case of the filter wheel and mount the empty cover of the filter wheel to the CCD, see Figure 2. |
- | - Now attach the filter wheel and the case of the adaptive optics module (AO), see Figure 3. | + | - now attach the filter wheel and the case of the adaptive optics module (AO), see Figure 3. |
- | - Attach | + | - attach |
- | - Connect | + | - connect |
- | * The AO control (flat ribbon cable) | + | * the AO control (flat ribbon cable) |
- | * The power supply | + | * the power supply |
- | - Ready :-) | + | - READY :-) |
- | <columns 100% 33% 33% 33%> | + | <WRAP group> |
- | [{{ : | + | <WRAP third column> |
+ | [{{ : | ||
+ | </ | ||
+ | <WRAP third column> | ||
+ | [{{ : | ||
+ | </ | ||
+ | <WRAP third column> | ||
+ | [{{ : | ||
+ | </ | ||
+ | </ | ||
- | < | ||
- | [{{ : | ||
- | <newcolumn> | + | <WRAP group> |
- | [{{ : | + | <WRAP third column> |
- | + | [{{ : | |
- | </ | + | </ |
- | + | <WRAP third column> | |
- | + | [{{ : | |
- | + | </ | |
- | <columns 100% 33% 33% 33%> | + | <WRAP third column> |
- | [{{ : | + | [{{ : |
- | + | </ | |
- | <newcolumn> | + | </ |
- | [{{ : | + | |
- | + | ||
- | <newcolumn> | + | |
- | [{{ : | + | |
- | </ |