Differences

This shows you the differences between two versions of the page.

--- en:ost:telescope:setup [2021/05/27 23:28] – [Setup of the mount] rhainich
+++ en:ost:telescope:setup [2024/07/11 07:45] (current) – [Refining the alignment] rhainich
@@ Line 1: / Line 1: @@
-FIXME <fs xx-large><fc #ff0000>This page is currently under revision.</fc></fs>
+====== Telescope setup and maintenance ======
-====== Telescope Setup ======
-===== Setup of the mount =====
+===== Setup of the GM4000 HPS II mount =====
-==== Using the mount directly ====
+==== Using the mount directly via the handheld terminal ====
 === Alignment ===
@@ Line 41: / Line 38: @@
     * to improve the accuracy all stars should be spread across the whole sky
-There are further methods to change/improve the alignment that are documented in the manual of the GM 4000 QCI, which can be found in room 2.009.
+There are further methods to change/improve the alignment that are documented in the manual of the GM 4000 HPS II, which can be found in room 2.009.
@@ Line 83: / Line 80: @@
 <WRAP twothirds column>
-The advantage of setting up the mount via the OMS is that a much more precise pointing model can be created, since not only a few stars are used, but up to 100 star fields distributed over the whole sky can be utilized. The exact position of these star fields is determined automatically with the help of the so-called [[https://en.wikipedia.org/wiki/Astrometric_solving | Plate Solving]].
+The advantage of setting up the mount via the OMS is that a much more precise pointing model can be created, since not only a few stars are used, but up to 100 star fields distributed over the whole sky can be utilized. The exact position of these star fields is determined automatically with the help of the so-called [[https://en.wikipedia.org/wiki/Astrometric_solving | Plate Solving]]. We use the software //ModelCreator//.
-We use the software //ModelCreator//.
+The most important settings in the **Equipment** tab such as **Camera**, **Mount**, **Solver**, and **Dome** should already be preset. These settings are stored as profiles. The predefined profiles can be selected from the **Profile** drop-down menu. By clicking on **Profiles** the profiles can be edited and also new ones can be created. By clicking on the ''Connect'' buttons at **Camera**, **Mount**, and **Dome** the corresponding devices can be connected to the //ModelCreator//. In the case of the camera, it must be ensured that the camera is connected beforehand to //MaxIm DL// because //ModelCreator// fetches the data from there.
-The most important settings in the **Equipment** tab such as **Camera**, **Mount**, **Solver** and **Dome** should already be preset. These settings are stored as profiles. The predefined profiles can be selected from the **Profile** drop-down menu. By clicking on **Profiles** the profiles can be edited and also new ones can be created. By clicking on the ''Connect'' buttons at **Camera**, **Mount** and **Dome** the corresponding devices can be connected to the //ModelCreator//. In the case of the camera, it must be ensured that the camera is connected beforehand to //MaxIm DL// because //ModelCreator// fetches the data from there.
+Next you should set the points where //ModelCreator// will create images of the sky. You should set a minimum height above the horizon (''Min Alt''), because points too close to the horizon do not make sense due to the long way the light travels through the atmosphere. It has been proven that at least a minimum altitude of 15° is necessary. Furthermore, it has turned out to be useful to activate the option ''Equal az spacing'' in order to achieve an optimized distribution of the points. If you also activate the option ''Show number'', the order in which the points are processed will also displayed. Afterwards you can click on **Generate** to generate the points. After that you can click on **Sort-EW** to sort the points from east to west. This significantly reduces the overall slewing time required by the mount. For our final pointing model we usually use up to 100 points. For this we usually set ''Points per row'' and ''Rows'' to 10 each. Additionally 3 base points can be selected. Click on the corresponding points with the mouse.
-Next you should set the points where //ModelCreator// will create images of the sky. You should set a minimum height above the horizon (''Min Alt''), because points too close to the horizon do not make sense due to the long way the light travels through the atmosphere. It has been proven that at least a minimum altitude of 15° is necessary. Furthermore, it has turned out to be useful to activate the option ''Equal az spacing'' in order to achieve an optimized distribution of the points. If you also activate the option ''Show number'' the order in which the points are processed is also displayed. Afterwards you can click on **Generate** to generate the points. After that you can click on **Sort-EW** to sort the points from east to west. This significantly reduces the overall slewing time required by the mount. For our final pointing model we usually use up to 100 points. For this we usually set ''Points per row'' and ''Rows'' to 10 each. Additionally 3 base points can be selected. Click on the corresponding points with the mouse.
 It has proven useful to increase the exposure time for points close to the horizon, because there the air mass increases significantly. Otherwise not enough objects can be identified. For points in the Milky Way, on the other hand, it can happen that no solution can be achieved by plate solving, because there seem to be too many stars in this area. In this case, it might be helpful to reduce the exposure time. The exposure time can be adjusted via the **Control** tab. Here you should also set a ''Slew settle time'' of 3s and the focal length of the telescope (''Focal Length'').
-Anschließend kann die Kalibration gestartet werden, indem man auf **Run** klickt. Vorher sollte noch sichergestellt werden, dass die Optionen ''Clear exsisting alignment'' und ''Sync align'' aktiviert sind. Anschließen fährt //ModelCreator// die Montierung nacheinander zu den einzelnen Punkten, macht dort eine Aufnahme, startet //PlateSolve//, sucht mit dessen Hilfe nach den genauen Koordinaten des Sternfelds, benutzt diese Lösung um das Pointing-Modell zu verbessern und macht anschließend mit dem nächsten Punkt weiter.
+Afterwards the calibration can be started by clicking **Run**. Before that, make sure that the options ''Clear exsisting alignment'' and ''Sync align'' are activated. Then //ModelCreator// moves the mount to the first point, takes an image, starts //PlateSolve//, searches for the exact coordinates of the star field, uses this solution to improve the pointing model and continues with the next point.
 <WRAP group>
 <WRAP third column>
-[{{ :ost:software:platesolve_2.png | //PlateSolve// - Bild geladen}}]
+[{{ :ost:software:platesolve_2.png | //PlateSolve// - Image loaded}}]
 </WRAP>
 <WRAP third column>
-[{{ :ost:software:platesolve_3.png | //PlateSolve// - Lösung gefunden}}]
+[{{ :ost:software:platesolve_3.png | //PlateSolve// - Solution found}}]
 </WRAP>
 <WRAP third column>
-[{{ :ost:software:platesolve_5.png | Aufgenommenes Sternfeld - Rote Kreuze: gefundene Sterne, Türkise Kreuze: Katalog Sterne, Gelbe Kreise: Identifizierter Stern}}]
+[{{ :ost:software:platesolve_5.png | Image of the star field - Red crosses: detected stars, Turquoise crosses: catalog stars, Yellow circles: identified stars}}]
 </WRAP>
 </WRAP>
+//PlateSolve// identifies the stars in the respective star field and compares their position with star catalogs. Starting from the coordinates provided by the telescope, a spiral outward search is performed. In the example above (the screenshot in the middle), the first step of the iteration was already successful and the star field was successfully identified. If the pointing model is not yet as good as in this example, which is usually the case when a completely new pointing model is created, it may take several iterations until the star field is identified. If after 99 iterations the star field has not been found, the iteration is aborted and //ModelCreator// moves on to the next pointing.
 </WRAP>
 <WRAP third column>
-{{ :ost:software:modelcreator_1.png |}}
+[{{ ost:software:modelcreator_1.png | //ModelCreator// - Equipment tab}}]\\
-{{ ost:software:modelcreator_3.png |}}
+[{{ ost:software:modelcreator_3.png | //ModelCreator// - Points tab with generated pointings}}]\\
-{{ ost:software:modelcreator_4.png |}}
+[{{ ost:software:modelcreator_4.png | //ModelCreator// - Control tab}}]
 </WRAP>
 </WRAP>
-//PlateSolve// identifiziert die Sterne in dem jeweiligen Sternfeld und vergleicht deren Position mit Sternkatalogen. Hierbei wird, ausgehend von den Koordinaten, die das Teleskop geliefert hat, spiralförmig nach außen gesucht. In dem Beisiel unten in der Mitte war bereits der erste Versuch erfolgreich und das Sternfeld wurde erfolgreich identifiziert. Wenn das Pointing-Modell noch nicht so gut ist wie in diesem Beispiel hier, was in der Regel der Fall ist wenn ein komplett neues Pointing-Modell erstellt wird, kann es durchaus einige Iterationen dauern, bis das Sternfeld identifiziert wird. Wenn nach 99 Iteration das Sternfeld nicht gefunden wurde, wird die Iteration abgebrochen und //ModelCreator// geht ohne Änderungen zum nächsten Punkt weiter.
 === Analyzing a pointing model ===
@@ Line 127: / Line 123: @@
 The Periodic Error Correction (PEC) can help to improve the tracking accuracy of the mounting by accounting for periodic errors of the worm gear. This error usually has a period of approx. 3 min 20 sec (3.3 minutes), while the PEC can correct for shorter periods, too. The error of the worm gear is usually irrelevant as long as the observations are only carried out with an eyepiece -- in case longer observations are taken with CCDs, the corrections of this error are getting important.
-The PEC has to be calibrated before it can operate properly. For this purpose, the mount needs detailed information on the deviations from the ideal tracking behavior. One possibility to achieve this is by centering a bright star in an eyepiece and following its motions with the hand terminal (the N - S - E - W buttons) for a while. A more sophisticated option is based on the [[en:ost:ccds:ccdops#Guiding|autoguide functionality]] of our CCD cameras, as the precision is higher this way. Start the PEC calibration on the hand terminal with:
+The PEC has to be calibrated before it can operate properly. For this purpose, the mount needs detailed information on the deviations from the ideal tracking behavior. One possibility to achieve this is by centering a bright star in an eyepiece and following its motions with the hand terminal (the N - S - E - W buttons) for a while. A more sophisticated option is based on the [[en:ost:ccds:ccdops#Guiding|autoguide functionality]] of our CCD cameras, as the precision is higher this way. It is recommended to train the PEC directly via the handheld terminal. The training algorithm of the PEC is started by means of:
 <code>Drive -> A-PEC control -> A-PEC Training</code>
@@ Line 133: / Line 129: @@
 In the next step choose the time period during which the PEC shall be "trained": 15, 30, or 60 minutes. The longer the training is, the better is the result of the PEC. After the training has been completed the corrections are calculated and the PEC is automatically activated.
-==== Pole hight adjustment ====
+==== Pole height adjustment ====
     * will follow...
-===== CDK20 =====
+===== Schmidt-Cassegrain telescopes (C14, C11, & C8) =====
-    * will follow ...
-===== C14 =====
 ====  Check and improve the collimation ====
@@ Line 166: / Line 158: @@
  **ATTENTION:** ONLY VERY MARGINAL CORRECTIONS NEED TO BE APPLIED TO THE SCREWS!
-==== Maintenance ====
+==== Maintaining the Schmidt plate ====
-=== Schmidt plate ===
+Do not touch and always put the lid on the telescope after observations to avoid unnecessary dust accumulation on the Schmidt plate! Especially in autumn and winter it is advisable to use the dew cap to prevent unnecessary condensation.
-Do NOT touch it and always keep the cover on the telescope (except during observations) so the plate will not get too dusty! Especially in autumn and winter, it is a good idea to use the dew cap to prevent unnecessary condensation.
+=== Cleaning ===
-**Cleaning:**
 <WRAP group>
 <WRAP half column>
-[{{ ost:telescope:schmidt_plate_dirty_rot.jpg | Dirty Schmidt plate}}]
+From time to time the Schmidt plates of our Schmidt-Cassegrain telescopes have to be cleaned. This is a difficult process, because we have to avoid at all costs that the Schmidt plate is damaged e.g. by scratches.
+**The following materials are required:**
+<WRAP half column>
+   * Distilled water
+   * Alcohol - isopropanol
+   * Cosmetic wipes or soft cellulose handkerchiefs that can be separated into the individual layers.
+     * **Very important:** The tissues must not contain lotions, odorants, or anything else along these lines
+   * Cotton balls
+   * Camel hair brush
+   * Microfiber cloth
+   * Pure dishwashing detergent with no other additives such as hand conditioners
+   * Optional: A small bellows or a compressed air bottle without propellant
 </WRAP>
 <WRAP half column>
-[{{ ost:telescope:schmidt_plate_clean.jpg?300 | Cleaned Schmidt plate }}]
+[{{ ost:telescope:cleaning_stuff.jpg?200 | Cleaning products}}]
 </WRAP>
+**Procedure:**
+  - The first thing to do is to put the telescope in a position where it looks a little bit towards the ground (if possible). In this way, cleaning fluid can be prevented from running into the telescope.
+  - Loose dust can be removed using the bellows or the compressed air bottle. Care must be taken to blow at as shallow an angle as possible onto the Schmidt plate to blow the dirt off the Schmidt plate and not push it further onto the Schmidt plate. With a compressed air bottle, do test sprays first so you can get a feel for how much air is coming out. In addition, this is a good way to make sure that the use of the compressed air bottle does not cause any additional deposits to form on the Schmidt plate.
+  - Next, further impurities can be removed using the camel hair brush.
+  - A mixture of distilled water and isopropanol in a ratio of 50:50 or 50:60 is suitable as a cleaning fluid. Furthermore, for heavily soiled surfaces, a little washing-up liquid can also be added. No more than 1 drop should be added per 500 ml of cleaning liquid, otherwise residues may remain on the Schmidt plate.
+  - If the Schmidt plate is heavily coated with sticky pollen, it is advisable to soak the deposit carefully. To do this, carefully apply a little cleaning liquid with a brush. Work in squares if possible.
+  - Then remove the heavy soiling with moistened cotton balls. Always work in straight lines, preferably from the inside to the outside, rotating the cotton ball so that the dirt adhering to the cotton ball does not rub over the surface. Use very little pressure and never rub in circles.
+  - Then remove the remaining impurities with moistened cosmetic tissues. For this purpose, again stroke in straight lines from the inside to the outside with light pressure, avoiding that the absorbed dirt rubs against the Schmidt plate.
+  - The cleaning liquid should dry off without leaving any residue. If this is not the case, the cleaning process should be repeated again with a newly prepared cleaning solution without detergent.
 </WRAP>
+<WRAP half column>
+[{{ ost:telescope:schmidt_plate_dirty_rot.jpg | Schmidt plate with dust and pollen}}]
+\\
+[{{ ost:telescope:schmidt_plate_clean.jpg?500 | Cleaned Schmidt plate}}]
+</WRAP>
+</WRAP>
+===== Corrected Dall-Kirkham telescope - CDK20 =====
+==== Collimation ====
+  * Will follow soon ...
+==== Cleaning the mirror ====
+To clean the mirror, basically the same steps must be followed as for cleaning the Schmidt plates on Schmidt-Cassegrain telescopes with the following exceptions:
+**Additional materials needed:**
+  * Paper towels
-    * More will follow...
+**Changes in procedure:**
+  * When cleaning the primary mirror:
+    - In addition, some paper towels should be placed in the carbon fiber sleeve around the mirror so that excess cleaning fluid is absorbed by them and does not run behind the mirror and come in contact with the electronics installed there. The paper towels must not come into contact with the mirror.
+  * When cleaning the secondary mirror:
+    - The telescope should look a few degrees above the horizon in this case.
 ===== Problems and their solution =====