Differences

This shows you the differences between two versions of the page.

--- en:ost:ccds:setup [2016/10/23 23:54] – [Assembling the filter wheel and the OAG] rhainich
+++ en:ost:ccds:setup [2021/03/31 07:53] (current) – [STF-8300M] rhainich
@@ Line 1: / Line 1: @@
 ====== CCDs Setup ======
+===== QHY600M =====
+   * will follow soon ...
 ===== STF-8300M =====
 ==== First light ====
-[{{:ost:ccds:windradani_small.gif?nocache|Wind turbines near Golm}}] [{{:ost:ccds:wissenschaft.jpg?335|One of the buildings in the Wissenschaftspark Golm}}]
-\\
+<WRAP group 70%>
+<WRAP half column>
-\\
+[{{ :ost:ccds:windradani_small.gif?nocache |Wind turbines near Golm}}]
+</WRAP>
+<WRAP half column>
+[{{ :ost:ccds:wissenschaft.jpg?335 |One of the buildings in the Wissenschaftspark Golm}}]
+</WRAP>
+</WRAP>
 ==== Assembling the filter wheel and the OAG ====
-The goal of this task is to mount or dismount the filter wheel and the OAG to the CCD. The procedure in short:
+The goal of this task is to mount or dismount the filter wheel and the off-axis guider (OAG) to the CCD. The procedure in short:
-  - Open the camera. Loose the screws from the cover, see Figure 1.
+  - to open the camera, loose the screws from the cover, see Figure 1.
-  - Open the case of the filter wheel and mount the backplate of the filter wheel (along with the mechanics and the electronics) to the CCD, see Figure 2.
+  - open the case of the filter wheel and mount the backplate of the filter wheel (along with the mechanics and the electronics) to the CCD, see Figure 2.
-  - Insert the individual filters and the spacer rings in the filter holder and mount the cover panel on top, see Figure 3. and 4.
+  - insert the individual filters and the spacer rings in the filter holder and mount the cover panel on top, see Figure 3. and 4.
-  - Attach the filter holder to the backplate of the filter wheel (be careful with the sensor for the filter position), see Figure 2. and 4.
+  - attach the filter holder to the backplate of the filter wheel (be careful with the sensor for the filter position), see Figure 2. and 4.
-  - Screw the cover of the filter wheel to the backplate of the filter wheel, see Figure 5.
+  - screw the cover of the filter wheel to the backplate of the filter wheel, see Figure 5.
-  - Attach the OAG to the filter wheel, see Figure 6.
+  - attach the OAG to the filter wheel, see Figure 6.
-  - Adjust the mirror of the OAG (the mirror is kept in place by means of a small lateral screw), see Figure 6.
+  - adjust the mirror of the OAG (the mirror is kept in place by means of a small lateral screw), see Figure 6.
-  - Attach the top cover and the T2 adapter to the OAG, see Figure 7.
+  - attach the top cover and the T2 adapter to the OAG, see Figure 7.
-  - Connect the cable of the filter wheel to the STF-8300, see Figure 8.
+  - connect the cable of the filter wheel to the STF-8300, see Figure 8.
-  - Fit the ST-i in the OAG, see Figure 9.
+  - fit the ST-i in the OAG, see Figure 9.
-  - Ready :-)
+  - READY :-)
-<columns 100% cm 33% cm 33% cm 33%>
+<WRAP group>
-[{{ :ost:ccds:stf8300_cover.jpg?300 | 1. Cover of the STF-8300 }}]
+<WRAP third column>
+[{{ :ost:ccds:stf8300_cover.jpg?265 | 1. Cover of the STF-8300 }}]
+</WRAP>
+<WRAP third column>
+[{{ :ost:ccds:stf8300_filter_wheel.jpg?265 | 2. Backplate of the filter wheel mounted to the SFT-8300 (the red circles mark the corresponding screws, the blue circle marks the sensor for the filter wheel position)}}]
+</WRAP>
+<WRAP third column>
+[{{ :ost:ccds:stf8300_filter_wheel_2.jpg?265 | 3. Filter holder with filters and spacer rings}}]
+</WRAP>
+</WRAP>
-<newcolumn>
-[{{ :ost:ccds:stf8300_filter_wheel.jpg?300 | 2. Backplate of the filter wheel mounted to the SFT-8300 (the red circles mark the corresponding screws, the blue circle mark the sensor for the filter wheel position)}}]
-<newcolumn>
+<WRAP group>
-[{{ :ost:ccds:stf8300_filter_wheel_2.jpg?300 | 3. Filter holder with filters and spacer rings}}]
+<WRAP third column>
+[{{ :ost:ccds:stf8300_filter_wheel_3.jpg?265 | 4. Filter wheel with inserted filter holder (the red circles mark the screws that attach the cover to the filter holder, the blue circles mark the screws that attach the filter holder to the backplate of the filter wheel)}}]
+</WRAP>
+<WRAP third column>
+[{{ :ost:ccds:stf8300_filter_wheel_4.jpg?265 | 5. Filter wheel with the cover}}]
+</WRAP>
+<WRAP third column>
+[{{ :ost:ccds:stf8300_oag_1.jpg?265 | 6. Filter wheel with the OAG}}]
+</WRAP>
+</WRAP>
-</columns>
+<WRAP group>
-<columns 100% cm 33% cm 33% cm 33%>
+<WRAP third column>
-[{{ :ost:ccds:stf8300_filter_wheel_3.jpg?300 | 4. Filter wheel with inserted filter holder (the red circles mark the screws that attach the cover to the filter holder, the blue circles mark the screws that attach the filter holder to the backplate of the filter wheel)}}]
+[{{ :ost:ccds:stf8300_oag_2.jpg?265 | 7. Filter wheel with the OAG and T2 adapter}}]
+</WRAP>
-<newcolumn>
+<WRAP third column>
-[{{ :ost:ccds:stf8300_filter_wheel_4.jpg?300 | 5. Filter wheel with cover}}]
+[{{ :ost:ccds:stf8300_side.jpg?265 | 8. Side view of the STF-8300}}]
+</WRAP>
-<newcolumn>
+<WRAP third column>
-[{{ :ost:ccds:stf8300_oag_1.jpg?300 | 6. Filter wheel with OAG}}]
+[{{ :ost:ccds:stf8300_complete.jpg?265 | 9. STF-8300 with filter wheel, OAG, and ST-i}}]
+</WRAP>
-</columns>
+</WRAP>
-<columns 100% cm 33% cm 33% cm 33%>
-[{{ :ost:ccds:stf8300_oag_2.jpg?300 | 7. Filter wheel with OAG and T2 adapter}}]
-<newcolumn>
-[{{ :ost:ccds:stf8300_side.jpg?300 | 8. Side view of the STF-8300}}]
-<newcolumn>
-[{{ :ost:ccds:stf8300_complete.jpg?300 | 9. STF-8300 with filter wheel, OAG and ST-i}}]
-</columns>
@@ Line 66: / Line 76: @@
 ==== Assembling the filter wheel ====
-The goal of this task is to mount or dismount the filter wheel to the CCD. The operation is demonstrated by the following pictures of the ST-8. The procedure in short:
+The goal of this task is to mount or dismount the filter wheel to the ST-7 of ST-8. The operation is demonstrated by the following pictures of the ST-8. The procedure in short:
-  - Open the camera. Loose the screws from the cover, see Figure 1.
-  - Open the case of the filter wheel and mount the empty cover of the filter wheel to the CCD, see Figure 2.
-  - Now attach the filter wheel and the case of the adaptive optics module (AO), see Figure 3.
-  - Attach the deflecting mirror and AO case, see Figure 4.
-  - Connect the cables for:
-    * The AO control (flat ribbon cable)
-    * The power supply
-  - Ready :-)
-<columns 100% 33% 33% 33%>
-[{{ :ost:ccds:st8_open_lid.jpg?300 |1: ST8 and cover}}]
-<newcolumn>
-[{{ :ost:ccds:fw_screws_2.jpg?300 |3: Mount the filter wheel}}]
-<newcolumn>
-[{{ :ost:ccds:fw_st8_ports.jpg?300 |5: Connect the cables}}]
-</columns>
+  - open the camera by loosing the screws from the cover, see Figure 1.
+  - open the case of the filter wheel and mount the empty cover of the filter wheel to the CCD, see Figure 2.
+  - now attach the filter wheel and the case of the adaptive optics module (AO), see Figure 3.
+  - attach the deflecting mirror and AO, see Figure 4.
+  - connect the cables for:
+    * the AO control (flat ribbon cable)
+    * the power supply
+  - READY :-)
-<columns 100% 33% 33% 33%>
+<WRAP group>
-[{{ :ost:ccds:fw_case.jpg?300 |2: Case and filter wheel}}]
+<WRAP third column>
+[{{ :ost:ccds:st8_open_lid.jpg?265 |1: ST8 and cover}}]
+</WRAP>
+<WRAP third column>
+[{{ :ost:ccds:fw_screws_2.jpg?265 |3: Screw positions on the filter-wheel backplate (green circles) and the AO case (red circles)}}]
+</WRAP>
+<WRAP third column>
+[{{ :ost:ccds:fw_st8_ports.jpg?265 |5: ST-8 with the cable connections}}]
+</WRAP>
+</WRAP>
-<newcolumn>
-[{{ :ost:ccds:fw_screws_1.jpg?300 |4: Adaptive Optics}}]
-<newcolumn>
+<WRAP group>
-[{{ :ost:ccds:fw_and_st8.jpg?300 |6: Complete}}]
+<WRAP third column>
+[{{ :ost:ccds:fw_case.jpg?265 |2: ST-8 with the attached filter-wheel case}}]
+</WRAP>
+<WRAP third column>
+[{{ :ost:ccds:fw_screws_1.jpg?265 |4: Adaptive optics module}}]
+</WRAP>
+<WRAP third column>
+[{{ :ost:ccds:fw_and_st8.jpg?265 |6: Assembled camera}}]
+</WRAP>
+</WRAP>
-</columns>