Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revisionBoth sides next revision | ||
en:ost:telescope:c8_bedienung [2018/01/24 14:44] – rhainich | en:ost:telescope:c8_bedienung [2018/01/26 14:02] – rhainich | ||
---|---|---|---|
Line 3: | Line 3: | ||
===== C8 (Under construction) ===== | ===== C8 (Under construction) ===== | ||
- | The Celestron 8 (C8) is our smallest telescope not accounting for binoculars or finderscopes. | + | The Celestron 8 (C8) is our smallest telescope not accounting for binoculars or finderscopes. |
- | === Setup === | + | ==== Assembly ==== |
- | In the following the setup of this telescope will be explained step by step. | + | In the following the setup of this telescope |
|< 100% 1% 30% 40% 25% >| | |< 100% 1% 30% 40% 25% >| | ||
| ^ Description | | ^ Description | ||
- | ^ 1 | One needs carefully choose the place where the telescope should be placed. For example, the relevant part of the sky needs to be visible (the dome covers part of the sky when the telescope is setup on the roof) and the cable connections for the power supply or the cameras should not become tripping hazards. The example setup was performed in the laboratory-course room directly | + | ^ 1 | One needs to carefully choose the place where the telescope should be placed. For example, the relevant part of the sky needs to be visible (the dome covers |
^ 2 | The tripod is the backbone of the telescope. | ^ 2 | The tripod is the backbone of the telescope. | ||
^ 3 | This disk is used to stabilize the legs of the tripod from the inside. The rod that punctures this disk will be screwed (with the side showing the thread) from below into the basis of the tripod. This needs to be done until the thread is completely visible on the other side. The rod should now be vertically slidable. | ^ 3 | This disk is used to stabilize the legs of the tripod from the inside. The rod that punctures this disk will be screwed (with the side showing the thread) from below into the basis of the tripod. This needs to be done until the thread is completely visible on the other side. The rod should now be vertically slidable. | ||
- | ^ 4 | Now the mount can be put on the tripod basis. One has to take care that little chromed pin needs to be placed | + | ^ 4 | Now the mount can be put on the tripod basis. One has to take care that little chromed pin from the basis of the tripod |
- | ^ 5 | Anbringung der Gegenwichtsstange und der Gegengewichte | + | ^ 5 | In the next step the counterweight bar and the counterweights needs to attached to the back-end of the mount. First the counterweight bar needs to thread into the opening of the declination axis. Afterwards the screw at the end of the counterweight bar can be removed and the counterweight can be place and fixated on the counterweight bar. Subsequently, |
- | ^ 6 | Anbringung des Tubus | {{ost: | + | ^ 6 | In the next step the tube needs to be attached to the mount. The tube is equipped with a so-called dove tail (the orange thing) that allows a quick and easy attachment of the tube to the mount. Simply, insert the dovetail into the clamp of the mount and tighten the screw of the clamp. |
- | ^ 6.5 | + | ^ 7 |
- | ^ 7 | + | ^ 8 |
- | ^ 9 | Achsen ausrichten | + | ^ 9 | If needed, the sun filter can be attached to the tube. Thread the screws on the side of the sun filter, so that it cannot fall off when the telescope is moving. |
- | ^ 10 | + | ^ 10 | Before using the telescope you have to tare the rotation axes. First lose the clutch knobs fixing the right-ascension axis, until you can freely move the telescope around this axis. Now adjust the position of the counterweight such that there is no movement along this axis anymore. Tighten the clutch knobs again and repeat this procedure for the declination axis. As there are no counterweights for this axis, one has to shift the tube along the clamp to tare the declination axis. | {{ost:c8:IMG_7108_small.jpg? |
- | ^ 11 | Gegebenfalls Sonnefilter anbringen | + | ^ 11 |
- | ^ 12 | Alignment ausfuehren, Genau wie am C11, [[en: | + | ^ 12 | Now the alignment can be performed. This procedure is very similar to the one of our |
- | ^ 11 | + | ^ 13 |
| | ||